Month: November 2020

DIY, Home improvement, Leakage, Toilet

Fix That Leaky Toilet, Save Your Money and the Environment

Fix Toilet Leaks-Save Money and Environment

https://commonhomerepair/toilet/leak/fix

Fix your leaky toilet. You can save money on your water bill and help to protect the environment by easily and quickly fixing your leaky toilet.

According to the US Environmental Protection Agency the average household’s leaks  can account for nearly 10,000 gallons of water wasted every year. The negative impact of that on the environment is disturbing, to the tune of nearly 1 trillion gallons nationwide in an estimated 11 million homes. That doesn’t even take into account the cost to consumer, which can not be overlooked. Simple home repair can help save you money and help save the environment at the same time. There are several potential causes for leaks in your toilet, however the most common is a faulty or worn flapper valve. I have included a link to a video for how to repair/replace that, as well as information about what else might cause this problem. To repair/replace the flapper valve in your toilet follow the simple steps below.

  1. Shut off the water supply valve behind your toilet. Remove the lid and flush the toilet to remove as much water as possible from the tank.
  2. Remove the lid on the tank of your toilet. Inside there is a lever and chain attached to the flapper valve at the bottom of the tank. Remove that chain from the lever, then disconnect the flapper valve from the drain that it is covering.
  3. Wipe around the drain before replacing the flapper valve to make sure there is no build up and you can get a tight seal with the new valve. Attach the new Flapper Valve directly over the drain and reattach the chain to the lever.
  4. Push on the flush mechanism to make sure that the flapper valve is aligned properly over the drain to create a seal.
  5. Then turn the water supply for your toilet back on, allow the tank to fill, listen and check to make sure there is no water leaking in the tank. Replace the lid and discard the old flapper valve. 

This video can give you the confidence to and know how to successfully replace your Flapper Valve.

Other Things to Keep In Mind

  • This link gives some of the most common causes of a leaky toilet, in addition to a faulty  flapper valve. If your toilet continues to leak check these other parts.

https://www.bobvila.com/articles/how-to-fix-a-running-toilet/

  • It’s particularly important, before refilling the tank, to check and readjust the chain that connects the new flapper valve to the lever to make sure it is raising and lowering the flapper valve right over the drain in order to get that proper seal once the tank is refilled.
  • It is helpful to have a few rags or work towels on hand in case something should happen or there are drips of water anywhere. Best to be prepared and not have to go search for them when you need one.
Drywall, Home improvement, Plaster, Spackle

Patch Your Drywall to Clean and Protect Your Walls

It’s not a big deal, just unsightly at first. However those small holes and cracks in your drywall can easily become larger when ignored and create more problems. As the mother of 2 grown children there are countless places where posters of the latest pop star or video game were hung, now just an unsightly little hole. Not to mention the time someone accidentally put a slightly larger hole in that wall while playing ball inside, I’m sure nobody knows who. Follow the steps below and fix those bothersome holes and cracks easily and efficiently. You can restore the look of your walls and protect them from further damage.

  1. Use a utility knife or a painter’s 5 in 1 tool to remove any cracked plaster, drywall, or chipped paint. You will want to pull away any loose debris or paper and make sure the surface is smooth.
  2. Use a flexible putty knife to apply spackle and fill in any small holes. Swipe on in smooth, even strokes and remove any excess as soon as possible. Follow manufacturer’s directions to let it dry and then buff with a block of fine  sandpaper.
  3. For slightly larger holes you will repeat the process of cleaning and smoothing the area, then apply self-adhesive, fiberglass mesh tape to cover  the whole following manufacturers directions.
  4. Repeat the process of applying spackle to cover the mesh tape, removing any excess with your spackle tool or putty knife. Allow the spackle to dry overnight and then smooth it over by using a block of fine grain sandpaper. It’s best to lay down a drop cloth first to catch the spackle dust that will fall and you may want to wear a mask so as not to inhale any.
  5. Once the process is complete you may need to add a second coat of spackle to make sure it is a completely smooth surface. Then you are ready to prime and paint.

* Below is a video to follow with all the directions for completing these steps and some additional tips and tricks to protect and preserve your walls.

Things to Avoid and Keep in Mind

  • Holes that are larger than 1 ½ inches or so probably need to be repaired with bridging material and a more complex process.
  • Allowing spackle to dry properly between applications is critical to get proper results. Take the time in the beginning to get a good result in the end.
  • When you are done sanding and smoothing the surface after your final coat of spackle it is helpful to use a slightly damp cloth to make sure all particles of dust are gone before applying any paint. You will get the best look and finish and your paint will adhere properly.